If you’re looking to Sell Ideal SignalTek Cable Qualification Tester

SignalTek Cable Performance Tester

Document Performance of Twisted Pair Voice and Data Cabling
SIGNALTEK™ provides a technically innovative method to test and document the performance of voice, data, and video applications for cabling installers and network technicians.

A technically innovative performance, monitoring and network troubleshooting tool

In addition to cable performance qualification, SIGNALTEK™ can be configured to run for several minutes or hours at a time. While stress testing critical network links, SIGNALTEK™ transmits hundreds of Gigabits of information across the network while looking for dropped packets. This monitoring mode allows SIGNALTEK™ to be used to isolate intermittent network problems that are difficult to detect. Adopting the latest generation of Gigabit Ethernet technology, IDEAL’s innovation brings the best performance to this new class of affordable testers.
Offers service detection to verify true 10/100/1000 Mbps Ethernet operation
Provides Bit Error Rate test for VoIP, data, and video-over-IP applications
User-defined data logging and network monitoring to detect problems that may cause network outages
Selectable test modes to qualify cabling support of Data, Voice over IP, and IP Video transmissions

High-Performance Gigabit Ethernet Testing
SIGNALTEK™ is the most cost-effective Gigabit Ethernet cable performance tester in the world. It tests the link’s ability to support applications by transmitting Ethernet packets on the link and measuring performance according to the IEEE 802.3ab Gigabit Ethernet standard, the ultimate performance indicator for any network.
Provides comprehensive cable testing for voice, data, and video applications
Performs complete wiremap and length tests of: 1, 3, and 4 pair UTP/STP, and series 6/59 coaxial cable to TIA-568 A/B and TIA-570 standards
Performs a full IEEE 802.3ab compliant Gigabit Ethernet packet test in about 35 seconds with 97% performance certainty
Includes a TDR (Time Domain Reflectometer) for accurate length measurements and to aide in locating cabling faults by providing distance to short/open information
Alligator clips allow testing of speaker, alarm, thermostat, home automation devices, and nearly any other type of control wire

A flexible tool to test any IP device
Internet Protocol (IP) is fast becoming the standard communications protocol for every type of network and home technology device. SIGNALTEK™ leverages its tri-speed (10/100/1000) Ethernet processor to provide performance and activity testing of any addressable IP device in the network.
IP pinging can be used to verify the communication of many devices including IP cameras, home automation, and A/V control panels
Offers network diagnostic tools such as link establishment, port LED blink, and ping
Supports static and dynamic (DHCP) IP configuration
Allows multiple target IP and web addresses for pinging several network devices and confirming operation of network switches and routers

SIGNALTEK™ makes reporting and data storage easy
The SIGNALTEK™ reporting and data storage system is designed for installers and network technicians with ease-of-use and flexibility in mind.
Generates easy pass/fail reports of link performance in accordance with IEEE 802.3ab standards
Stores 20,000+ records on internal memory
Accepts USB memory drives for unlimited storage
Direct printing to supported USB printers
No special software required, view reports with any web browser

Buying, Selling, Trading Ideal SignalTek

Features:
Gigabit Performance Qualification
Test to IEEE 802.3 standards
Selectable Performance Testing
Qualify performance of Data, Voice over IP, and IP Video applications
Performs Gigabit Ethernet link establishment test in 10 seconds
Data Monitoring
To detect intermittent network problems
Smart Autotest Function
detects the presence of the SIGNALTEK remote, active network device or open ended cable and automatically runs the appropriate test suite
Intuitive Graphical User Interface
for fast and easy operation
Internal and USB Data Storage
store 20,000 tests internally or unlimited on USB drive
Prints Easy-to-Read Pass/Fail Qualification Reports

If you’re selling your Ideal SignalTek please fill out form on the right hand side of page.

If you’re looking to Sell Ideal LANTEK 2 1000 Cat6 Cat6a LAN Cable Certfier

Features

• Best price/performance options – models ranging from 350 MHz to 1000 MHz for Category 6/ISO E through Category 7A/ISO FA certification
• High speed testing saves time and money
• Most internal memory available – store over 1700 Category 6/ISO E tests with graphs
• Patented testing method – eliminate expensive permanent link adapters and test with patch cords for most installation
• Extraordinary fast fiber testing with FiberTEK® FDX – the first dual wavelength, bidirectional fiber certification tool
• Large, ultra-bright display – 4.3 in. wide screen display with white LED backlighting provides easy viewing of high-frequency data plots
• 350 MHz & 500 MHz models are fully upgradable to 1000 MHz
• Smart lithium-ion battery technology – 18 hour battery life with self calibrating “fuel gauge” for accurate capacity readings

LanTEK II offers the best speed, performance and price available today. Nine second Cat 5E and 14 second Cat 6 tests with full performance data plus 10 Gigabit Alien Crosstalk testing that’s more than 4x faster than other systems making LanTEK II the ultimate copper certification platform. The patented universal adapter system lets you certify most cabling with off-the-shelf patch cords saving time and money by eliminating the need for proprietary permanent link adapters.

The optional FiberTEK® FDX modules provide the world’s only dual wavelength, bidirectional fiber certification available. That’s more than 3x faster than existing testers. Three models provide the needed performance without the added expense; choose from 350 MHz/Cat 6, 500 MHz/Cat 6A or 1000 MHz/Cat7A all with accuracy independently verified by ETL.

LanTEK II also offers ultimate versatility with options for certification of TERA, GG45 and EC7 category 7/7A systems, plus M12 industrial Ethernet and coaxial test adapters.

Universal Link Testing
The patented testing process eliminates the need for costly permanent link adapters. By using universal test adapters for Category 5E through 6A certification, patch cords are typically the only item that needs to be replaced when worn or damaged. This eliminates the wait and expense of proprietary adapters meaning more time is spent testing and less time searching for replacement parts.

Channel and Permanent Link Testing with One Adapter
Only LanTEK allows permanent link and channel certification without changing adapters. The patented DualMODE™ function allows cabling to be certified to two different standards with one press of the Autotest button; half the time it would take with any other certifier.

Certify cabling to both Category 6 permanent link and Category 6 channel link standards at the same time, satisfying requirements from cabling manufacturers and end users without costing any more time in the field. Or certify cabling to existing current standards and proposed future standards which eliminates retesting at a later date.

Fast Test Times
Category 5E certification in 11 seconds, Category 6 in 14 seconds, and Category 6A in only 16 seconds with graphs! Plus enjoy fiber certification that’s 3x faster and 10 gigabit alien crosstalk certification that’s 4x faster than the competition.

Most Memory Capacity
LanTEK II has 7x the storage capacity as competitive certifiers. Save an astonishing 1700 Category 6 results with graphs. If the memory fills, simply off-load the data to a USB flash drive for portability and archiving.

Cut the Power Cord
The new smart lithium battery technology provides an amazing 18 hours of use in the field. The revolutionary battery technology has two charging modes that offer the best flexibility available. Slow charge the battery overnight while it is inside the LanTEK II, or remove the battery and plug in to its dedicated charging port for a quick five hour charge. Plus, the battery’s internal fuel gauge automatically selfadjusts every time the pack is completely discharged and recharged, providing accurate charge readings over the life of the battery pack.

Three Models to Suit Any Need
LanTEK II is offered in three models: 350, 500 and 1000. The LanTEK II-350 offers 350MHz of frequency sweep to certify Category 6 cabling and below. LanTEK II-500 sweeps to 500MHz, and is the only certifier designed specifically for Category 6A cabling. LanTEK II-1000 is the world’s fastest certifier with a full 1GHz of certification bandwidth to go well beyond Category 7/ISO Class F (600MHz), all the way to ISO Class FA (1000MHz) standard to support shared sheath applications such as CATV, Ethernet and voice in the same cable.

Buying, Selling, Trading Ideal LANTEK 2

Maximum Reporting Power
The new IDEAL DataCENTER (IDC) software puts the power in the fingertips of the user. The main test grid display can be customized to display and sort by virtually any test parameter allowing for quick identification of tests that are below desired performance margins. Quickly scan through plot data by choosing a plot type and scrolling through the test list to instantly refresh the plot for each test. This makes visually scanning through reports and searching for anomalies a breeze. IDC offers many reporting options such as detailed, brief, and single line reports, plus export data in XML, CSV and PDF formats. Plus the unique ability to customized the plots by inverting the scales, toggling linear or log frequencies and even adjusting colors makes IDC the most user friendly and powerful cable reporting software ever.

If you’re selling your Ideal LANTEK 2 please fill out form on the right hand side of page.

If you’re looking to Sell Wavetek LANTEK PRO XL 1300nm Cat5 Cable Certifier

LANTEK PRO XL … Certify with Confidence.

Confidence and speed! The two qualities you need most to certify and troubleshoot your LAN installation. Confidence to know your LAN meets TIA and ISO standards. And speed to do your job efficiently and economically. In less than 30 seconds, the Autotest completes line map, DC loop resistance, length, capacitance, Dual Next, attenuation and Attenuation-to-Crosstalk Ratios (ACR) measurements. The LANTEK PRO gives you tremendous speed advantage, without compromising performance. Our advanced  design guarantees TSB-67 Level II accuracy for basic and channel links

The LANTEK PRO XL stores up to 500 Autotests. You can easily print each test or download all the tests into a PC for later use. You can even sort test results! Users can select TIA or ISO Autotest suites to automatically perform all the tests required by the respective standard. Cable types and test suites can be customized by the user to adapt to specific needs.

Buying, Selling, Trading Wavetek LANTEK PRO XL

The LANTEK PRO XL also comes with built-in troubleshooting using Cable Expert.
If Autotest fails, a simple press of the button enables Cable Expert to highlight the suspected problem and display troubleshooting advice describing both the problem and the possible causes.
Test 1300nm Fiber Optic Cabling Installations!
Fiber Optic Cable power loss measurements capability for the LANTEK PRO XL! With the FIBERKIT, the LANTEK PRO XL directly displays optical power loss through fiber cable, splices and connectors. With this powerful but simple fiber conversion, you can verify proper connection of fiber cabling with the same LANTEK PRO XL you use for copper cable. LANTEK PRO XL has some of the same Testing features that the Fluke DSP Test Sets has.
Save big dollars with the convenience of a Copper and Fiber Tester.

If you’re selling your Wavetek LANTEK PRO XL please fill out form on the right hand side of page.

If you’re looking to Sell Wavetek FIBERKIT+ SM MM Fiber Test Kit

LT8000 FIBERKITS

• Tests Multimode and Singlemode fiber for power loss
• LED and laser light sources generate 850 nm and 1300 nm wavelengths on Multimode cable 1310 nm and 1550 nm on Singlemode cable
• One power meter to test both Multimode and Singlemode

Buying, Selling, Trading Wavetek FIBERKIT+

Features:

• Automatically test multiple wavelengths without changing connectors or switching settings
• LED and laser light sources generate 850nm wavelengths on Multimode cable
• Label and organize test results by direction, drop, project and job. Upload stored fiber tests and create reports using LT Record Manager PC software
• Supports multiple fiber optic connector configurations

If you’re selling your Wavetek FIBERKIT+ please fill out form on the right hand side of page.

If you’re looking to Sell Wavetek LANTEK PRO XL Cat5 850nm Fiber Certifier

LANTEK PRO XL … Certify with Confidence.

Confidence and speed! The two qualities you need most to certify and troubleshoot your LAN installation. Confidence to know your LAN meets TIA and ISO standards. And speed to do your job efficiently and economically. In less than 30 seconds, the Autotest completes line map, DC loop resistance, length, capacitance, Dual Next, attenuation and Attenuation-to-Crosstalk Ratios (ACR) measurements. The LANTEK PRO gives you tremendous speed advantage, without compromising performance. Our advanced  design guarantees TSB-67 Level II accuracy for basic and channel links

Buying, Selling, Trading Wavetek LANTEK PRO XL

The LANTEK PRO XL stores up to 500 Autotests. You can easily print each test or download all the tests into a PC for later use. You can even sort test results! Users can select TIA or ISO Autotest suites to automatically perform all the tests required by the respective standard. Cable types and test suites can be customized by the user to adapt to specific needs.

The LANTEK PRO XL also comes with built-in troubleshooting using Cable Expert.
If Autotest fails, a simple press of the button enables Cable Expert to highlight the suspected problem and display troubleshooting advice describing both the problem and the possible causes.
Test 850nm Fiber Optic Cabling Installations!
Fiber Optic Cable power loss measurements capability for the LANTEK PRO XL! With the FIBERKIT, the LANTEK PRO XL directly displays optical power loss through fiber cable, splices and connectors. With this powerful but simple fiber conversion, you can verify proper connection of fiber cabling with the same LANTEK PRO XL you use for copper cable. LANTEK PRO XL has some of the same Testing features that the Fluke DSP Test Sets has.
Save big dollars with the convenience of a Copper and Fiber Tester.

If you’re selling your Wavetek LANTEK PRO XL please fill out form on the right hand side of page.

If you’re looking to Sell IDEAL LANTEK 6A SM MM Fiber Cat5e Cat6 Certfier

Features:

• DUALmode Testing to save Time: Reports channel and permanent link test results simultaneously
• Test with Patchcords toSave Money: Performs CAT5e/6/6a/ISO-D/E/Ea testing with standard patchords to reach the lowest cost of ownership
• The Industries first Certifier designed specifically to support the emerging Category 6a cabling standard
• Certifies to 500MHz to support 10 gigabi ethernet (10GbE) applications
• Includes new high performance adapters that support channel and permanent link certification of TIA5e/6/6a and ISO D/E/Ea UTP and STP cabling
• Meets proposed Level IIIe accuracy requirements
• Independently verified by ETL for baseline, channel and permanent link accuracy

LANTEK offers a family of high performance cable certification testers to support a full range of LAN cable testing. The LANTEK family of certification testers uses the IDEAL patented measurement system that removes the effects of ordinary patchcords, thus making channel and permanent link certification of a cable standard such as CAT6a or ISO-F possible without changing adapters. The same patented technology also makes DUALmode Testing possible so the users can get any two test results simultaneously. As a result, the LANTEKs save you money and time on the job.

LANTEK 6A 500MHz is designed to support the emerging CAT6a Standard to certify LAN cabling to support applications up to 10G Ethernet.

Buying, Selling, Trading IDEAL LANTEK 6A SM MM

The Only Tester in the World to Support DUALmode Testing to Save Time and Labor

Save time and money by simultaneously conducting any combination of two tests with LANTEK 6/6A/7G. For example, you can select a combination of channel/permanent link or CAT6a/ISO-F standards and get both test results in virtually the same amount of time as a single test. DUALmode can be used as either a troubleshooting tool or to provide an extra level of confidence to your customers by performing certification to additional test standards that demonstrate the quality of your work

Unique Adapter Scheme Reduces Cost of Ownership

LANTEK cable testers utilize an advanced link adapter method to reduce cost of ownership. All testers come with universal link adapters that are used for basic, channel, and permanent link testing. These channel adapters fit into the case of the unit and are locked in place. This creates a stable and repeatable testing platform while eliminating bulky adapters that extend beyond the end of the unit. Simply plug in the appropriate reference patchcord to the channel adapter, to perform permanent link testing.

If you’re selling your IDEAL LANTEK 6A SM MM please fill out form on the right hand side of page.

If you’re looking to Sell Wavetek LANTEK PRO XL Cat5 Cable Tester Certifier

Confidence and speed! The two qualities you need most to certify and troubleshoot your LAN installation. Confidence to know your LAN meets TIA and ISO standards. And speed to do your job efficiently and economically. In less than 30 seconds, the Autotest completes line map, DC loop resistance, length, capacitance, Dual Next, attenuation and Attenuation-to-Crosstalk Ratios (ACR) measurements. The LANTEK PRO gives you tremendous speed advantage, without compromising performance. Our advanced design guarantees TSB-67 Level II accuracy for basic and channel links

The LANTEK PRO XL stores up to 500 Autotests. You can easily print each test or download all the tests into a PC for later use. You can even sort test results! Users can select TIA or ISO Autotest suites to automatically perform all the tests required by the respective standard. Cable types and test suites can be customized by the user to adapt to specific needs.

Buying, Selling, Trading Wavetek LANTEK PRO XL

The LANTEK PRO XL also comes with built-in troubleshooting using Cable Expert. If Autotest fails, a simple press of the button enables Cable Expert to highlight the suspected problem and display troubleshooting advice describing both the problem and the possible causes. Fiber Optic Cable power loss measurements capability for the LANTEK PRO XL! With the FIBERKIT, the LANTEK PRO XL directly displays optical power loss through fiber cable, splices and connectors. With this powerful but simple fiber conversion, you can verify proper connection of fiber cabling with the same LANTEK PRO XL you use for copper cable. LANTEK PRO XL has some of the same Testing features that the Fluke DSP Test Sets has. Save big dollars with the convenience of a Copper and Fiber Tester.

If you’re selling your Wavetek LANTEK PRO XL please fill out form on the right hand side of page.

If you’re looking to Sell IDEAL LANTEK 6A Multimode Fiber Cable Certifier

Features:

• DUALmode Testing to save Time: Reports channel and permanent link test results simultaneously
• Test with Patchcords toSave Money: Performs CAT5e/6/6a/ISO-D/E/Ea testing with standard patchords to reach the lowest cost of ownership
• The Industries first Certifier designed specifically to support the emerging Category 6a cabling standard
• Certifies to 500MHz to support 10 gigabi ethernet (10GbE) applications
• Includes new high performance adapters that support channel and permanent link certification of TIA5e/6/6a and ISO D/E/Ea UTP and STP cabling
• Meets proposed Level IIIe accuracy requirements
• Independently verified by ETL for baseline, channel and permanent link accuracy

Buying, Selling, Trading IDEAL LANTEK 6A Multimode

LANTEK offers a family of high performance cable certification testers to support a full range of LAN cable testing. The LANTEK family of certification testers uses the IDEAL patented measurement system that removes the effects of ordinary patchcords, thus making channel and permanent link certification of a cable standard such as CAT6a or ISO-F possible without changing adapters. The same patented technology also makes DUALmode Testing possible so the users can get any two test results simultaneously. As a result, the LANTEKs save you money and time on the job.

LANTEK 6A 500MHz is designed to support the emerging CAT6a Standard to certify LAN cabling to support applications up to 10G Ethernet.

The Only Tester in the World to Support DUALmode Testing to Save Time and Labor

Save time and money by simultaneously conducting any combination of two tests with LANTEK 6/6A/7G. For example, you can select a combination of channel/permanent link or CAT6a/ISO-F standards and get both test results in virtually the same amount of time as a single test. DUALmode can be used as either a troubleshooting tool or to provide an extra level of confidence to your customers by performing certification to additional test standards that demonstrate the quality of your work

Unique Adapter Scheme Reduces Cost of Ownership

LANTEK cable testers utilize an advanced link adapter method to reduce cost of ownership. All testers come with universal link adapters that are used for basic, channel, and permanent link testing. These channel adapters fit into the case of the unit and are locked in place. This creates a stable and repeatable testing platform while eliminating bulky adapters that extend beyond the end of the unit. Simply plug in the appropriate reference patchcord to the channel adapter, to perform permanent link testing.

Fiber Adapters

The multimode 850nm/1300nm LanTek fiber adapters are the perfect solution for certifying or troubleshooting fiber backbones and fiber to the desktop installations in commercial buildings or campus environments. Working with LANTEK® 6 & 7, it measures signal loss and length over Multimode fiber. With an easy fiber adapter switch, it can support dual wavelength and bidirectional testing.

Using adapters, the LANTEK display unit can measure length in the loop-back mode. Using it in both the display and remote units, the system can measure signal loss and length with dual wavelength and bi-directional capabilities.

If you’re selling your IDEAL LANTEK 6A Multimode please fill out form on the right hand side of page.

If you’re looking to Sell Ideal 1310 SM Tracetek Fiber Adapter

IDEAL 1310 SM Tracetek Adapter
With TRACETEK™, the LANTEK® series of cable certifiers can now troubleshoot fiber optic installations.

Troubleshooting fiber has traditionally been done with an OTDR, but now TRACETEK offers a much simpler and cost-effective solution. TRACETEK can graphically display the fiber under test allowing pin-point location of events and faults on multimode and singlemode cables without the high costs normally associated with buying or renting an OTDR. Time on the job is further reduced with simple one-button operation.

TRACETEK works by injecting pulsed laser light into one end of the fiber and measuring the amount of light that is reflected back from events along the fiber cable. These reflections are then processed and plotted on the LANTEK 1/4 VGA color display.

Events, like connectors, show up as spikes on the display. A bad splice will result in more light being reflected back, thus geneating a bigger spike. The amplitude of the spike gives an indication of optical return loss, thus identifying the trouble spot. While using TRACETEK, a cursor can scroll along the trace to provide a reading of distance to the event.

TRACETEK can graphically display and store fiber traces. LANTEK Reporter Software provides file management, report generation, and printing of all test results. TRACETEK is the only fiber accessory for a LAN cable certifier that will trace a fiber run, provide distance-to-fault along the fiber and display the relative magnitude of the event.

When used together, TRACETEK and  FIBERTEK Adapters provide LANTEK series of cable certifiers a unique combination of fiber measurement, documentation and trouble shooting capabilities. It is a cost effective fiber certification solution to meet the requirements of the proposed TIA TSB-140.

Buying, Selling, Trading Ideal 1310 SM

Features:

• Provides an easy to use troubleshooting capability for fiber optic cables
• Illustrates distance-to-fault by providing magnitude and distance of reflective events
• Presents graphical information of fiber under test—similar to an expensive OTDR
• Measures total fiber length without remote handset or second operator
• Requires only one LAN cable certifier for copper and fiber testing and troubleshooting

If you’re selling your Ideal 1310 SM please fill out form on the right hand side of page.

If you’re looking to Sell Wavetek FS 850 Light Source for LT8000 FiberKit

MM FiberKit Features:
– Test Multimode fiber optic cable systems for power loss.
– Automatically test multiple wavelengths without changing connectors or switching settings.
– LED and laser light sources generate 850nm and 1300nm wavelengths on Multimode cable.
– Label and organize test results by direction, drop, project and job. Upload stored fiber tests and create reports using LT Record Manager PC software.
– Supports multiple fiber optic connector configurations.
– Compatible with Wavetek LT8155 and LT8600 Cable Analyzers.
– Only the 850nm Light Source Uncluded

Buying, Selling, Trading Wavetek FS 850

Included:
* Wavetek FS+ 850 850nm Light Source
* (1) Multimode ST To ST Fiber Patch Cord
* (1) ST Connectors

If you’re selling your Wavetek FS 850 please fill out form on the right hand side of page.